• Plastic barrel garden chair

    This article describes all the necessary actions for a plastic chair, which you can do at home without any problems thanks to this information. In the description, everything is clear and without unnecessary terms with the correct sequence of actions. After reading, you will not have unnecessary questions, and you will easily be ready to proceed to the implementation of the interior element of your garden, and maybe another part of your home area. You will like this chair for its practicality and quite a large fortress, despite the fact that it is made of plastic. You should not spend a lot of money on branded chairs, surprise your friends and relatives by making your own construction from an ordinary plastic barrel, practically without spending on finances from the family budget.
    Plastic Barrel Garden Chair

    Tools Required

    The Most Important Tools in Doing Your Workbecome:
    • jigsaw (you can use high-quality steel knife or a grinder);
    • drill (even a manual one will do);
    • soldering iron,
    • rivets;
    • screwdriver;
    • sandpaper;
    • wooden meter;
    • bucket of water and a clean rag.

    Getting Started

    The first step, which you need to perform, so it's a good wash the barrel, so that you enjoyed working with it. Having prepared all the necessary tools in advance, you can start work that does not take a lot of work and time if you carefully study everything and carry out the sequence of actions correctly.

    Measuring and cutting the barrel

    When you do this work forget that it is better to measure seven times, and once cut off and not vice versa. Also, do not forget about safety, as electric and sharp instruments will be used. Measure the height of the barrel and divide it in half. After that, at least six places around the middle of the barrel should be placed approximately at equal distances from each other, this will ensure you to draw a straight line and cut the barrel exactly in the middle. For cutting, the fret saw is ideal, but if it is not there, use the tool that you can perform this action. Then proceed to the measurements of the upper part of the barrel you cut off. You need to trim the top of the barrel to avoid irregularities. If you use a barrel with a closing lid, then you just need to cut the thread or the place of fixing the lid.
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair made of plastic barrels
    When you have a cylinder, you also need to cut it in half, but not horizontally, but vertically. In order to do this exactly, observe the correctness of measurements. Put a wooden meter on top of the cylinder, which must be level and without any defects.Measure on both sides of the meter distance to it, it should be the same. When you have thus identified the middle, you make notes on the barrel at both ends of the meter. Then measure around the circumference the distance between the points and move the notes to the bottom of the cylinder, then you can connect them and you get smooth lines. After you cut, you have two semicircular plates, one of which should be put off for the time being. Next, one plate will perform the role of the back of the chair and armrests, on which you need to properly fold them. To do this, take a ruler, measure horizontally the middle (at the ends of the plate) and mark with dots, after that, along the circle at the level of the middle, mark the 20 cm. Draw the line from point to point, then draw upwards and you will have a square. Cut from the top to the bottom along the line from both sides and on this preparation for the soldering of this element is ready. But for more comfortable armrests, you will need to once again divide the squares into halves and fold the squares, then solder them, or fix them with screws or rivets. For bonding it is worthwhile just to drill holes in the planes in the right places of the joint.You can make a slightly different shape and size in contrast to the above example, just consider that the backrest must be strong. The second plate will serve as an amplifier for the backrest and armrests. To do this, you need to cut out small plates from it, which will be attached to the main structure of the backrest in the form of overlays. It is advisable to fasten them to each other with rivets. The material is enough for you, even some elements will remain after cutting the secondary plate, and the pieces that may seem unnecessary will still be useful to you if you want to add personality to your chair and decorate, additionally cutting out the figurines at your discretion and fixing it on the structure.
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel

    Assembling the structure

    This action is performed directly with a soldering iron or a blowtorch. Much better and more accurate will get a chair, working as a blowtorch. If you are going to do everything with a soldering iron, then do not forget that for a solid construction you need to solder joints on both sides.
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    Garden chair from plastic barrel
    The chair for the garden of plastic barrels
    In general, put the base, which consists of the bottom of the barrel,a lid or a cut-off upper part of the barrel lays down on it and is gently soldered in a circle, after which you will have a strong base on which you can sit. If you do not do this, you will get a chair with an opening top, but this affects the strength and reliability. Upstairs we put the back made and just as carefully solder in the joints. If you worked as a soldering iron, then you can get uneven seams, which should be cleaned with sandpaper. After that the chair is almost ready, it only remains to strengthen the back and the armrests with pre-cut pieces of plastic. You can also cut a comfortable plate on which you will be more comfortable to sit. Fix them in the right places on the heels and your chair is completely ready for use. If you wish, you can paint the chair, after which it will get a much better look, and you can use it wherever you want. And so, without spending much time and effort, you will have an original chair for everyday use. Such a work can be done without any special skills and abilities by any person.

    Related news


    How to set up Asus netbook
    How to connect a router to a modem
    What does omg mean
    How to pickle vegetables in a hurry
    How to build maps
    How to make a real fruit and berry fruit juice
    Buttercup Earrings
    Where in Petersburg you can order delicious pizza without mushrooms